AX3000T 刷 immortalwrt后 改变灯光为 系统启动正常后60秒关闭灯光,PPOE网络不正常,闪烁

AX3000T 刷 immortalwrt 改变灯光为 改为系统启动正常后60秒关闭灯光,Wan网络不正常,闪烁

文件位置/etc/init.d/led
既然知道文件了,那么,丢进CHATGPT,修改为如下

#!/bin/sh /etc/rc.common
# Copyright (C) 2008 OpenWrt.org

START=96

led_color_set() {
    local cfg="$1"
    local sysfs="$2"

    local max_b
    local colors
    local color
    local multi_intensity
    local value
    local write

    [ -e /sys/class/leds/${sysfs}/multi_intensity ] || return
    [ -e /sys/class/leds/${sysfs}/multi_index ] || return

    max_b="$(cat /sys/class/leds/${sysfs}/max_brightness)"
    colors="$(cat /sys/class/leds/${sysfs}/multi_index | tr " " "\n")"
    multi_intensity=""
    for color in $colors; do
        config_get value $1 "color_${color}" "0"
        [ "$value" -gt 0 ] && write=1
        [ "$value" -gt "$max_b" ] && value="$max_b"
        multi_intensity="${multi_intensity}${value} "
    done

    # Check if any color is configured
    [ "$write" = 1 ] || return
    # Remove last whitespace
    multi_intensity="${multi_intensity:0:-1}"

    echo "setting '${name}' led color to '${multi_intensity}'"
    echo "${multi_intensity}" > /sys/class/leds/${sysfs}/multi_intensity
}

load_led() {
    local name
    local sysfs
    local trigger
    local dev
    local ports
    local mode
    local default
    local delayon
    local delayoff
    local interval

    config_get sysfs $1 sysfs
    config_get name $1 name "$sysfs"
    config_get trigger $1 trigger "none"
    config_get dev $1 dev
    config_get ports $1 port
    config_get mode $1 mode
    config_get_bool default $1 default "0"
    config_get delayon $1 delayon
    config_get delayoff $1 delayoff
    config_get interval $1 interval "50"
    config_get port_state $1 port_state
    config_get delay $1 delay "150"
    config_get message $1 message ""
    config_get gpio $1 gpio "0"
    config_get_bool inverted $1 inverted "0"

    [ "$2" ] && [ "$sysfs" != "$2" ] && return

    # execute application led trigger
    [ -f "/usr/libexec/led-trigger/${trigger}" ] && {
        . "/usr/libexec/led-trigger/${trigger}"
        return 0
    }

    [ "$trigger" = "usbdev" ] && {
        trigger="usbport"
        ports=$(echo "$dev" | sed -n 's/^\([0-9]*\)-\([0-9]*\)$/usb\1-port\2/p')
        [ -z "$ports" ] && ports=$(echo "$dev" | sed -n 's/\./-port/p')
    }

    [ -e /sys/class/leds/${sysfs}/brightness ] && {
        echo "setting up led ${name}"

        printf "%s %s %d" \
            "$sysfs" \
            "$(sed -ne 's/^.*\[\(.*\)\].*$/\1/p' /sys/class/leds/${sysfs}/trigger)" \
            "$(cat /sys/class/leds/${sysfs}/brightness)" \
                >> /var/run/led.state
        [ -e /sys/class/leds/${sysfs}/multi_intensity ] && {
            printf " %s" \
                "$(sed 's/\ /:/g' /sys/class/leds/${sysfs}/multi_intensity)" \
                >> /var/run/led.state
        }
        printf "\n" >> /var/run/led.state

        [ "$default" = 0 ] &&
            echo 0 >/sys/class/leds/${sysfs}/brightness

        [ $default = 1 ] &&
            cat /sys/class/leds/${sysfs}/max_brightness > /sys/class/leds/${sysfs}/brightness

        led_color_set "$1" "$sysfs"

        echo $trigger > /sys/class/leds/${sysfs}/trigger 2> /dev/null
        ret="$?"
        [ $ret = 0 ] || {
            echo >&2 "Skipping trigger '$trigger' for led '$name' due to missing kernel module"
            return 1
        }
        case "$trigger" in
        "heartbeat")
            echo "${inverted}" > "/sys/class/leds/${sysfs}/invert"
            ;;
        "netdev")
            [ -n "$dev" ] && {
                echo $dev > /sys/class/leds/${sysfs}/device_name
                for m in $mode; do
                    [ -e "/sys/class/leds/${sysfs}/$m" ] && \
                        echo 1 > /sys/class/leds/${sysfs}/$m
                done
                echo $interval > /sys/class/leds/${sysfs}/interval 2>/dev/null
            }
            ;;
        "timer"|"oneshot")
            [ -n "$delayon" ] && \
                echo $delayon > /sys/class/leds/${sysfs}/delay_on
            [ -n "$delayoff" ] && \
                echo $delayoff > /sys/class/leds/${sysfs}/delay_off
            ;;
        "usbport")
            local p
            for p in $ports; do
                echo 1 > /sys/class/leds/${sysfs}/ports/$p
            done
            ;;
        "port_state")
            [ -n "$port_state" ] && \
                echo $port_state > /sys/class/leds/${sysfs}/port_state
            ;;
        "gpio")
            echo $gpio > /sys/class/leds/${sysfs}/gpio
            echo $inverted > /sys/class/leds/${sysfs}/inverted
            ;;
        switch[0-9]*)
            local port_mask speed_mask
            config_get port_mask $1 port_mask
            [ -n "$port_mask" ] && \
                echo $port_mask > /sys/class/leds/${sysfs}/port_mask
            config_get speed_mask $1 speed_mask
            [ -n "$speed_mask" ] && \
                echo $speed_mask > /sys/class/leds/${sysfs}/speed_mask
            [ -n "$mode" ] && \
                echo "$mode" > /sys/class/leds/${sysfs}/mode
            ;;
        esac
    }
}

start() {
    [ -e /sys/class/leds/ ] && {
        [ -s /var/run/led.state ] && {
            local led trigger brightness color
            while read led trigger brightness color; do
                [ "$1" ] && [ "$1" != "$led" ] && continue
                [ -e "/sys/class/leds/$led/trigger" ] && \
                    echo "$trigger" > "/sys/class/leds/$led/trigger"

                [ -e "/sys/class/leds/$led/brightness" ] && \
                    echo "$brightness" > "/sys/class/leds/$led/brightness"

                [ -e "/sys/class/leds/$led/multi_intensity" ] && \
                    echo "$color" | sed 's/:/\ /g' > \
                        "/sys/class/leds/$led/multi_intensity"
            done < /var/run/led.state
            if [ "$1" ]; then
                grep -v "^$1 " /var/run/led.state > /var/run/led.state.new
                mv /var/run/led.state.new /var/run/led.state
            else
                rm /var/run/led.state
            fi
        }

        config_load system
        config_foreach load_led led "$1"

        # 等待60秒后关闭灯光
        sleep 60
        for led in /sys/class/leds/*; do
            [ -e "$led/brightness" ] && echo 0 > "$led/brightness"
        done &

        # 检查PPPoE网络状态并闪烁灯光
        while true; do
            if ! ip link show | grep -q ppp; then
                for led in /sys/class/leds/*; do
                    [ -e "$led/brightness" ] && {
                        echo 1 > "$led/brightness"
                        sleep 0.5
                        echo 0 > "$led/brightness"
                        sleep 0.5
                    }
                done
            fi
            sleep 5
        done &
    }
}